To insure compatibility between releases
of HyperWare-II and the firmware running in the IntelliLogger,
the version numbers of HyperWare-II and the IntelliLogger
firmware must match as described per the following.
To check the current Version Number
of your currently installed HyperWare-II, select the Help/About menu
choice from the opening Communications Window.
To check the current firmware version
installed in the IntelliLogger, view the current version
via the top line of the LCD on the IntelliLogger or use
a Status inquiry via a PC connected to the IntelliLogger
via browser or HyperWare-II.
Version compatibility is dictated by the second number
set within the version number. To be compatible,
these numbers must be the same. For example if
the IntelliLogger has version 1.3.4.5 and the HyperWare-II
is version 1.3.6.8, then the HyperWare-II and Firmware
are compatible as both have the number 3 as the second
number set.
Following is a listing of available downloads. The
currently installed firmware version is viewed via the
top line of the IntelliLogger LCD or use a Status inquiry
via a PC connected to the IntelliLogger via browser or
HyperWare-II.
Step 1: Download
and unzip the desired firmware version (below) into
a temporary directory. You will have a file named IL_Reflash_Ver_x_x_x_x.bin,
the x’s indicate the most recently released version.
Step 2: Start
HyperWare-II and connect to the IntelliLogger you wish
to reflash.
Step 3: In
the Menu, Select Logger, Reflash Firmware and point
to the .bin file you have just downloaded. Continue
for 4-5 minutes to complete the update. A dialog
box will open indicating reflash progress and when
completed the message “Reflash
Complete” is displayed.
Click on the link or right-click and select Save
Target As… to download the update.
Version 1.6.2.1 (Released
5-29-07) Note: Upgrade to Build 2036 of Hyperware when using this.
Version 1.7.1.3 (Released
6-12-07)
Version 1.8.3.2 (Released
6-28-07) Note: Upgrade to Build 2040 of Hyperware when using this.
Version 1.12.1.6 (Released
9-27-07) Note: Upgrade to Build 2041 of Hyperware when using this.
Version 1.13.1.2 (Released
10-17-07) Note: Upgrade to Build 2042 of Hyperware when using this.
Version 1.14.1.4 (Released
2-29-08) Note: Upgrade to Build 2043 of Hyperware when using this.
Following is a listing of
available downloads of the HyperWare-II software. HyperWare-II listing
is presented by “Build Number” . The
“Build Number” identifies a set of files
(any number of which may have been updated) that make
up a complete release of HyperWare-II. To check
the Build Number of your currently installed HyperWare-II,
select the Help/About menu choice from the opening
Communications Window.
Step 1: Download the HyperWare Build
file and save it in a temporary directory.
Step 2: Unzip* the file to a temporary
directory.
Step 3: Close HyperWare-II and all
other programs. From within the temporary directory run
Setup.exe and install the program in the same directory
as the original installation. This will keep all current
settings available in the newly installed program. This
completes the software update.
BUILD
2036 (RELEASED 5-29-07)
BUILD
2038 (RELEASED 6-12-07)
BUILD
2040 (RELEASED 6-28-07)
BUILD
2041 (RELEASED 9-27-07)
BUILD
2042 (RELEASED 10-17-07)
BUILD
2043 (RELEASED 2-29-08)
*Note: If you have trouble unzipping
these files, please visit www.winzip.com for more information.
